<div dir="ltr">Look at pre-punched dishes for cases. Easier to make a big square hole and use the dish to cover your cut edges.  Penn-Elcom has a bunch of combo's available.</div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Sat, Jan 31, 2026 at 11:35 PM Joe via Stagecraft <<a href="mailto:stagecraft@theatrical.net">stagecraft@theatrical.net</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div><div style="font-family:"Helvetica Neue",Helvetica,Arial,sans-serif;font-size:16px"><div><div dir="ltr">I am working to make a custom DMX to Relay box.  The circuit board has Relays installed, and the power connections and DMX connections are all screw terminals.</div><div dir="ltr">The reason I am not simply using a dimmer pack set to serve as on/off only mode, is that I have both 120v and 12vDC voltages. The 12vDC will be to trigger sprinkler valves that are part of two air-cannons. The 120v will be to power a miniature xenon strobe.   Though, perhaps I can use a standard dimmer pack, and just plug 12vDC power supplies for the two channels I need the DC control.  I am a little concerned that the inductive relays on the water valves may not play well with my 12v wall warts.  I suppose some diodes at the solenoid may solve that.</div><div dir="ltr"><br></div><div dir="ltr">Note that the DMX, 3-channel Relay module I have, has screw terminals for all in/outputs.</div><div dir="ltr"><br></div><div dir="ltr">When I have made a similar custom pack in the past. I obtained some XLR Panel connectors.  But, drilling the holes in the box was both frustrating and not really good enough, even if I got it to function.  I looked for, but didn't find any generic pre-punched panels to attach the two XLR connectors. Though, I did find ones with 4 or 8 locations.</div><div dir="ltr">Also, the box has to provide for the 120vAC, and 12vDC in/out.  In the past, I just used cut extension cords, with a strain relief. The 12v was easy, just a circular panel mount outlet.</div><div dir="ltr"><br></div><div dir="ltr">I feel I am somehow not finding the right stuff to do this easily, and professional looking.</div><div><br></div><div dir="ltr">As I wright this, I think I am convincing myself to just use a standard DMX dimmer pack.  But, decided to go ahead and post, in case anyone has anything to suggest.</div><div dir="ltr"><br></div><div dir="ltr">Are there any 4-channel dimmer or relay packs that are for lower wattage, and so are packaged without the weight/size of the higher wattage units?  Perhaps in the form factor of a power strip? I know heavy-weight often means rugged. But there is also a kind of ruggedness that comes with things that are small and light weight.</div><div dir="ltr"><br></div><div><div style="font-family:Helvetica,Arial,sans-serif;font-size:16px"><div dir="ltr" style="font-family:Helvetica,Arial,sans-serif;font-size:16px">-Joe</div></div></div></div></div></div>____________________________________________________________<br>
For list information see <<a href="http://stagecraft.theprices.net/" rel="noreferrer" target="_blank">http://stagecraft.theprices.net/</a>><br>
Stagecraft mailing list<br>
<a href="mailto:Stagecraft@theatrical.net" target="_blank">Stagecraft@theatrical.net</a><br>
<a href="http://theatrical.net/mailman/listinfo/stagecraft_theatrical.net" rel="noreferrer" target="_blank">http://theatrical.net/mailman/listinfo/stagecraft_theatrical.net</a><br>
</blockquote></div>